Product ID:5 MINUTE EPOXY RESIN
MSDS Date:12/14/1989
FSC:8040
NIIN:01-034-0401
Kit Part:Y
MSDS Number: BLJLZ

Emergency Phone: 508-777-1100

Info Phone: 508-777-1100

Cage: 16509

Telephone: 508-777-1100

Cage: 16509

BISPHENOL A DIGLYCIDYL ETHER RESIN (POTENTIAL SKIN

CAS: 25068-38-6

RTECS: KD4380000

Fraction By Weight: > 60%

0 LBS/GAL (EPA REFERENCE METHOD 24)

RTECS: 9999999VO

LD50 LC50 Mixture:ORAL LD50 (RAT):11,400 MG/KG *
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PROLONGED OR REPEATED SKIN CONTACT MAY
CAUSE SENSITIZATION, WITH ITCHING, SWELLING, OR RASHES ON LATER
EXPOSURE. *DERMAL LD50 (RABBIT): >20,000 MG/KG. INHALATION
LC50 (RAT): NO DEATHS IN SATURAT ED AIR; EXPOSURE TIME 8 HOURS.
Effects of Overexposure:EYES:MILD IRRITATION. SKIN:MILD IRRITATION.
INHALATION:NO DATA. THE LOW VAPOR PRESSURE OF THE RESIN MAKES
INHALATION UNLIKELY IN NORMAL USE. INGESTION:ACUTE ORAL TOXICITY IS
LOW. MAY CAUSE GASTRIC DIS TRESS.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, OR OTHER SKIN
DISORDERS.

First Aid:EYES:FLUSH W/CLEAN WATER FOR 15 MIN WHILE GENTLY HOLDING
EYELIDS OPEN.GET IMMED MED ATTN.SKIN:WASH THOROUGHLY W/SOAP & WARM
WATER.CONSULT A PHYSICIAN IF IRRIT DEVELOPS.INHALATION:REMOVE
PATIENT TO FRE SH AIR.GIVE OXYGEN IF BREATHING IS DIFFICULT.GET MED
ATTN IF SYMPTOMS PERSIST.INGESTION:DO NOT INDUCE VOMITING.GIVE TWO
GLASSES OF WATER TO DILUTE(UNLESS PATIENT IS UNCONSCIOUS).GET
MEDICAL ATTN.

Flash Point Method:PMCC
Flash Point:<400F,<204C
Extinguishing Media:CO2, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS AND PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:PREVENT SKIN AND EYE CONTACT. LARGE SPILLS MAY
BE ABSORBED ON INERT MATERIAL SUCH AS SAND OR VERMICULITE. SCRAPE
SPILL UP INTO NONPOROUS CONTAINER. CLEAN SPILL AREA WITH STRONG
DETERGENT AND WATER. US E SOLVENTS ONLY WITH APPROPRIATE CAUTION.

Handling and Storage Precautions:STORE IN A COOL,DRY PLACE.HANDLE MIXED
RESIN & HARDENER IN ACCORDANCE WITH THE POTENTIAL HAZARD OF THE
CURING AGENT USED.REMOVE CONTAMINATED CLOTHES**
Other Precautions:**AND PROTECTIVE GEAR. CLEAN THOROUGHLY BEFORE USING
AGAIN. DISCARD CONTAMINATED LEATHER ARTICLES. WASH THOROUGHLY AFTER
USING, PARTICULARLY BEFORE EATING OR SMOKING.

Respiratory Protection:NONE REQUIRED AT NORMAL HANDLING TEMPERATURES.
Ventilation:LOCAL EXHAUST IS RECOMENDED FOR CONFINED AREAS. GENERAL
MECHANICAL IS ADEQUATE FOR NORMAL USE.
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:SAFETY GLASSES WITH SIDE SHIELDS.
Other Protective Equipment:OTHER GEAR AS REQUIRED TO PREVENT SKIN
CONTACT.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING, PARTICULARLY
BEFORE EATING OR SMOKING.
Supplemental Safety and Health
THIS INFO APPLIES TO RESIN PART OF KIT. AFTER CURING, THE PRODUCT IS
NON-HAZARDOUS.

Vapor Pres:NIL
Vapor Density:> 1
Spec Gravity:1.2
pH:7 (5%)
Evaporation Rate & Reference:< 1 (BUAC=1)
Solubility in Water:NIL
Appearance and Odor:THICK, AMBER LIQUID WITH LITTLE ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:OPEN FLAME AND EXTREME HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON, ALDEHYDES AND ACIDS
FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS GENERATED WHEN THIS RESIN IS
MIXED WITH AMINES OR EPOXY HARDENERS. BE CAREFUL WHEN MIXING LARGE
AMOUNTS.

Waste Disposal Methods:REMOVE TO A WASTE FACILITY OPERATING IN
COMPLIANCE WITH STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.